+高级检索
方形叠层橡胶隔震支座竖向力学性能试验研究
DOI:
作者:
作者单位:

作者简介:

通讯作者:

基金项目:


Experimental Study of Square Laminated Rubber Bearings on the Vertical Mechanic Characteristics for Isolation
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
    摘要:

    为了研究方形天然胶叠层橡胶支座的竖向刚度与面压、形状系数的相关性,对4个不同形状系数的、边长为400 mm的足尺方形天然胶叠层橡胶隔震支座,分别施加10 MPa,12.5 MPa,15 MPa的面压,进行了竖向力学性能试验,得到4个支座不同面压下的竖向刚度.分析了竖向刚度与面压、形状系数的相关性,得到了竖向刚度与面压相关性的经验公式.研究表明:天然胶叠层橡胶隔震支座的竖向刚度与面压相关,面压增大时,支座的竖向刚度增大;面压不变时,竖向刚度随第2形状系数的增大而增大;第2形状系数较大时,竖向刚度对面压的变化更为敏感.

    Abstract:

    order to study the effect of compressive stress and shape factors on the vertical stiffness of square laminated rubber bearings, serial compression tests were conducted on four 400×400 mm2 full scale square laminated rubber bearings at stresses of 10 MPa,12.5 MPa and 15 MPa. The relation between the vertical stiffness, shape factors and compressive stress of the four bearings was studied and an experimental expression was obtained. The tests and analysis results have shown that the vertical stiffness of the laminated rubber bearing is compressive stress dependent, the vertical stiffness increases when the compressive stress increases; at constant compressive stress, the increase of the second shape factors will lead to the increase of vertical stiffness; and the compressive stress has more influence on vertical stiffness when the bearing has a large second shape factor value.

    参考文献
    相似文献
    引证文献
文章指标
  • PDF下载次数:
  • HTML阅读次数:
  • 摘要点击次数:
  • 引用次数:
引用本文

苏 键,温留汉·黑沙,周福霖.方形叠层橡胶隔震支座竖向力学性能试验研究[J].湖南大学学报:自然科学版,2011,38(7):20~24

复制
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期:
  • 出版日期:
作者稿件一经被我刊录用,如无特别声明,即视作同意授予我刊论文整体的全部复制传播的权利,包括但不限于复制权、发行权、信息网络传播权、广播权、表演权、翻译权、汇编权、改编权等著作使用权转让给我刊,我刊有权根据工作需要,允许合作的数据库、新媒体平台及其他数字平台进行数字传播和国际传播等。特此声明。
关闭