+高级检索
Mn13Cr2高锰钢冲击磨损机制的研究
DOI:
作者:
作者单位:

作者简介:

通讯作者:

基金项目:


Research on Impact Wear Mechanism of High Manganese Steel Mn13Cr2
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
    摘要:

    采用冲击磨料磨损试验机、扫描电镜等仪器设备,通过模拟高锰钢零件的实际工况条件,研究不同冲击功条件下材料的磨损规律以及磨损机理.研究结果表明:将高锰钢加热到650 ℃保温2 h,再加热到1 080 ℃保温2 h,然后淬火处理,其晶粒明显细化;高锰钢的临界冲击功为2 J/mm2,高锰钢在超过临界冲击功的条件下使用时才能充分发挥其加工硬化作用;高锰钢冲击磨损过程中主要存在切削磨损和凿削磨损两个磨损机制;冲击磨损试验后高锰钢晶粒内出现了大量的滑移带,滑移带密度随着冲击功的增加而增大,在2 J/mm2时,甚至出现了交滑移现象.

    Abstract:

    By using the impact abrasive wear testing machine to simulate the actual working conditions of high manganese steel parts, the wear mechanism of high manganese steel under different impact loads was investigated with scanning electron microscopy and other equipment. The result indicates the grain of the high manganese steel is smaller after the heat treatment process, which firstly heats the high manganese steel to 550 ℃ for 1.5 hours, secondly heats it to 650 ℃ for 2 hours, and then heats it to 1 080 ℃ for 2 hours, and quenches it at last. The relate impact load of 2J/mm2 is the critical impact load of high manganese steel. High manganese steel fully plays its work hardening effect when the relate impact load is above the critical impact load. There are two wear mechanisms: cutting mechanism and pit mechanism. After impact abrasive wear test, there are a large number of slip bands in high manganese steel, and the slip bands' density increases when the relate impact load increases. When the relate impact load is 2 J/mm2, the cross slip is found in the grains.

    参考文献
    相似文献
    引证文献
文章指标
  • PDF下载次数:
  • HTML阅读次数:
  • 摘要点击次数:
  • 引用次数:
引用本文

张福全 ,邵飞杰, 周惦武. Mn13Cr2高锰钢冲击磨损机制的研究[J].湖南大学学报:自然科学版,2014,41(12):6~10

复制
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2015-01-05
  • 出版日期:
作者稿件一经被我刊录用,如无特别声明,即视作同意授予我刊论文整体的全部复制传播的权利,包括但不限于复制权、发行权、信息网络传播权、广播权、表演权、翻译权、汇编权、改编权等著作使用权转让给我刊,我刊有权根据工作需要,允许合作的数据库、新媒体平台及其他数字平台进行数字传播和国际传播等。特此声明。
关闭