+高级检索
循环荷载作用下新型钢筋套筒灌浆连接结构性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

基金项目:


Structural Performance of Innovative Grout Sleeve Splicing for Rebars under Cyclic Loading
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
    摘要:

    为降低钢筋连接成本,利用普通无缝钢管通过冷滚压工艺加工了一种新型钢筋连接用灌浆套筒,并制作了12个钢筋连接接头试件,通过反复拉压试验及单向拉伸试验研究其连接结构性能.结果表明,该连接能够满足JGJ107-2010规定的强度及变形要求;接头经过反复拉压循环加载后,钢筋极限黏结强度较直接拉伸试件约降低10%;由于套筒的约束作用,钢筋套筒灌浆连接残余黏结强度大于极限抗拉强度的50%;套筒每端内壁环肋数量不宜少于3道,并应根据接头承载力要求的提高而适当增加.

    Abstract:

    To reduce the cost of bar splice, a new type of grouted sleeve was developed with standard seamless steel tube through cold rolling techniques. Based on this sleeve, twelve coupler specimens were prepared and tested under cyclic load as well as incremental tensile load. The structural performance of this novel grouted splice was then studied. The test results showed that the strength and deformation of the splices could satisfy the requirements specified in the JGJ107-2010. Due to the cyclic loads, the ultimate bond strength declined by about ten percent of the specimen strength under direct tension test. Meanwhile, because of the confinement provided by the sleeve, the residual bond strength of the bond failed specimen is greater than 50 percent of the ultimate tensile strength. Moreover, it is found that the number of the concentric ribs at each side of the sleeve should not be less than three, and it should be increased properly for the improvement of tensile capacity requirement of the splice.

    参考文献
    相似文献
    引证文献
文章指标
  • PDF下载次数:
  • HTML阅读次数:
  • 摘要点击次数:
  • 引用次数:
引用本文

郑永峰,郭正兴.循环荷载作用下新型钢筋套筒灌浆连接结构性能[J].湖南大学学报:自然科学版,2016,43(11):131~140

复制
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2016-11-21
  • 出版日期:
作者稿件一经被我刊录用,如无特别声明,即视作同意授予我刊论文整体的全部复制传播的权利,包括但不限于复制权、发行权、信息网络传播权、广播权、表演权、翻译权、汇编权、改编权等著作使用权转让给我刊,我刊有权根据工作需要,允许合作的数据库、新媒体平台及其他数字平台进行数字传播和国际传播等。特此声明。
关闭