+高级检索
节理面形貌参数相关性分析及粗糙度量化分级研究
DOI:
作者:
作者单位:

作者简介:

通讯作者:

基金项目:


Analysis on Parameter Correlation of Joint Surface Morphology and Study on Quantitative Classification of Roughness
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
    摘要:

    以岩石自然节理面为研究对象,对节理面形貌进行了测量,建立了节理面三维形貌图,在此基础上计算得到了5个形貌参数,以中心线平均高度均方根为基准,对参数之间的相关性进行了研究.在形貌参数测量的基础上,选取3个形貌参数,采用模糊数学方法,实现节理面粗糙度的量化,对粗糙度进行了分级,并对形貌参数与粗糙程度指标之间的依存关系进行了研究.研究表明,中心线平均高度与均方根呈线性正比例关系,峰态系数、偏度系数及表面微凸体倾角均方根值与中心线平均高度均方根值的比值与中心线平均高度的均方根值为幂函数关系.粗糙度量化分级研究结果表明,粗糙度量化分级指标与静摩擦因数及静摩擦角有明显正比例线性关系,静摩擦因数、静摩擦角及量化分级指标与中心线平均高度均方根值的比值与中心线平均高度均方根值为幂函数关系.通过各参数相互之间的定量函数关系,可得到相关性系数,进而实现形貌参数对节理面粗糙程度及摩擦力的估算.

    Abstract:

    Taking the rock nature joint surface as the research object, the morphology of joint surface was measured and 3D shape of the joint surface was established. On the basis of this, five parameters were calculated and the correlation between parameters was studied taking the root mean square value(RMS) as benchmark. Selecting three morphology parameters, the method of fuzzy mathematics was used to quantify the roughness of joint surface, and the roughness was classified. Meanwhile, the correlation between the morphology parameter and roughness index was studied. The results show that the average height of the central line is proportional to its RMS. The relation among the ratio of kurtosis coefficient, skewness coefficient, micro convex angle and RMS of mean height of centerline is power functions. The results of quantitative classification of roughness show that the quantitative classification index and friction coefficient and friction angle have obvious positive proportional linear relationship. It can be used for the estimation of joint surface friction. The relation among the ratio of friction coefficient, friction angle, the quantitative classification index and RMS of mean height of centerline is also power functions. Through the quantitative function relationship between the parameters, the correlation coefficient can be obtained, and then the estimation of surface roughness and friction force of the joints can be realized.

    参考文献
    相似文献
    引证文献
文章指标
  • PDF下载次数:
  • HTML阅读次数:
  • 摘要点击次数:
  • 引用次数:
引用本文

付建新,宋卫东?覮,谭玉叶.节理面形貌参数相关性分析及粗糙度量化分级研究[J].湖南大学学报:自然科学版,2019,46(1):124~132

复制
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2019-01-23
  • 出版日期:
作者稿件一经被我刊录用,如无特别声明,即视作同意授予我刊论文整体的全部复制传播的权利,包括但不限于复制权、发行权、信息网络传播权、广播权、表演权、翻译权、汇编权、改编权等著作使用权转让给我刊,我刊有权根据工作需要,允许合作的数据库、新媒体平台及其他数字平台进行数字传播和国际传播等。特此声明。
关闭